Type tray - allows only continuous walls
style of the fingers
space at the start and end in multiple of normal spaces
height of the bottom lips sticking out (multiples of thickness) FingerHoleEdge only!
space below holes of FingerHoleEdge (multiples of thickness)
extra material to grind away burn marks (multiples of thickness)
width of the fingers (multiples of thickness)
extra space to allow finger move in and out (multiples of thickness)
space between fingers (multiples of thickness)
width of finger holes (multiples of thickness)
inside angle of the feet
height of strips to be glued to the inside of bottom edges (multiples of thickness)
height of the feet (multiples of thickness)
distance from finger holes to bottom edge (multiples of thickness)
width of the feet (multiples of thickness)
have lid overlap at the sides (similar to OutSetEdge)
set to lower value to get disks surrounding the pins
diameter of the pin hole (multiples of thickness)
fixed length of the grips on he lids (multiples of thickness)
thickness of the arc holding the pin in place (multiples of thickness)
diameter of the pin hole in mm
pieces per hinge
number of hinges per edge
style of hinge used
radius of the eye (multiples of thickness)
space between eyes (multiples of thickness)
minimum space around the hinge (multiples of thickness)
width of the "finger hole" in mm
additional pin for better positioning
position(s) of the extra locking springs in the lid
angle of the hooks bending outward
radius at the bottom (multiples of thickness)
length of the hooks (multiples of thickness)
height above the wall
radius of hole
radius of top corner
extend the triangle along the length of the edge (multiples of thickness)
head diameter of mounting screw (in mm)
shaft diameter of mounting screw (in mm)
minimum space left and right without holes (fraction of the edge length)
number of mounting holes (integer)
side of box (not all valid configurations make sense...)
edge style
height above the wall in mm
height of hole(s) in percentage of maximum hole height (handle height - 2 * material thickness)
width of hole(s) in percentage of maximum hole width (width of edge - (n+1) * material thickness)
added to side panels if checked, to front and back otherwise (only used with top_edge parameter)
radius of corners in mm
extend the handle along the length of the edge (multiples of thickness)
type of handle
type of lid to create
height of the handle in multiples of thickness (if applicable)
height of the brim in multiples of thickness (if any)
play when sliding the lid on in multiples of thickness (if applicable)
Textsize in mm for the traycontent
Text Alignment
Distance in X from edge of tray in mm. Has no effect when text is centered.
Distance in Y from edge of tray in mm.
Start compartement labels on the front
Every line is the text for one compartment. Beginning with front left
depth of the hole in mm (in addition to the relative)
width of the hole in mm (in addition to the relative)
maximal radius (in mm)
depth of the hole as fraction of the wall
width of the hole as fraction of the wall width
sections left to right in mm π
sections back to front in mm π
inner height in mm (unless outside selected)
inner height of inner walls in mm (unless outside selected)(leave to zero for same as outer walls)
treat sizes as outside measurements π
edge type for bottom edge
edge type for top edge
additional height of the back wall - e top edge only
radius for strengthening side walls with back_height
height of the grip hole in mm
width of th grip hole in mm (zero for no hole)
add handle to the bottom (changes bottom edge in the front)
Decide which outer walls should have finger hole, too
Thickness of the material [mm]
Burn correction [mm] (bigger values for tighter fit)
Format of the resulting file
Label the parts (where available)
Print reference rectangle with given length [mm] (0 to disable)
Width of tabs holding parts in place [mm]
Add a QR Code with link or command line to the generated output
Style for inner corners
Spacing around parts (multiples of thickness [: extra space in mm])
Print surrounding boxes for some structures
Boxes.py
Boxes.py
